MicroLog works with the following external sensors:
DT132 (2.5m) External Temperature Sensor
This MicroLog sensor takes external temperature measurements in a wider range than the internal temperature sensor. With a faster response time than the internal sensor, it enables measuring materials that cannot be measured with the internal sensor.
Specifications:
| Range: | -50 °C to 100 °C |
| Resolution: | Better than 2 °C |
| Accuracy: | ± 2% of reading |
| Probe Length: | 100 mm |
| Probe OD: | 3.2 mm |
| Max. Temperature: | 150 °C |
Download External Temperature Sensor PDF file
DT093 External Temperature Sensor with 8m Probe
| Range: | -50 °C to 100 °C |
| Resolution: | Better than 2 °C |
| Accuracy: | ±2% of reading |
| Probe Length: | 100 mm |
| Probe OD: | 3.2 mm |
| Max. Temperature: | 100 °C |
DT140 0-10 Volt Sensor
A general sensor that will measure any device or transmitter that produces a linear analog 0-10V output. The voltage can easily be converted to the correct measured units with the help of the Microlab program.
Specifications:
| Range: | 0-10 V |
| Resolution: | 0.05 V |
| Accuracy: | ± 3% before calibration |
| Input Impedance: | 3 M |
| Calibration: | Two point calibration |
| OV Protection: | +30 V |
Download 0-10 Volt Sensor PDF file
DT139 0-20 mAmp External Sensor
This MicroLog external sensor can sample any device or transmitter, producing a linear current between 0-20 mAmp. The 0-20 mAmp can be converted to the correct measured units by using Microlab¹s calibration option.
Specifications:
| Range: | 0-20 mA |
| Resolution: | ± 0.1 mA |
| Accuracy: | ± 3 before calibration |
| Calibration: | Two point calibration |
| OC Protection: | 55 mA |
Download 0-20 mAmp External Sensor PDF file
DT141 External Contact Adapter
This MicroLog sensor monitors Reed Relay contacts and switch status (open/closed), to identify the correlation between phenomena such as temperature change and door status.
Specifications:
| Range: | Open/Close |
| Connector: | Screw Terminal |
| Cable Length: | 2.5 m |
| Internal Pull-Up Resistor: | No need for external power source |
Download External Contact Adapter PDF file
DT168 External pH Adaptor
| Range: | 0-14 pH |
| Resolution: | 0.116 pH |
| Accuracy: | 5% of reading |
| Calibration: | Offset calibration |
External PT100 Temperature Adaptor
| Range: | -10 °C to 10 °C /
-100 °C to 120 °C |
| Resolution: | 0.1 °C / 1.1 °C |
| Accuracy: | ± 0.25 °C / ± 1°C |
| Connector: | Screw Terminal |
DT279 Conductivity Adapter and Electrode
| Range: | 0–20 mS |
| Resolution: | 0.04 mS |
| Accuracy: | 3% |
| Response Time: | Less than 1 minute |
DT163 Light
| Light Range: | 0 – 5000 Lux |
| Resolution: | 25 Lux |
| Accuracy: | 20% of reading |
| Built-in Sensors:
Temperature
Humidity
External Sensors: LCD units icons: ˚C, ˚F, %RH, pH, V, mA, mS Temperature
Voltage
Current
pH
Conductivity
|
|||||||||||||||||||||||||||||||||||||||||||